-
Happymodel Crux3 1S ELRS 3 Inch Analog Toothpick
Noticed: Not include the Insta360 go2 or CaddxFPV peanut camera. Features: 40gram 1s brushless Toothpick drone AIO Flight controller with ELRS Receiver and 5.8G VTX CADDX ANT Camera New 1202.5 KV11500 brushless motor Recommend to use 1s 450mah/650mah/660mah/720mah battery Compatible with CaddxFPV Peanut and Insta360 GO2 Carrying Caddxfpv peanut Got 4.5 minutes flying time with […]Rp1.790.000 -
Happymodel Crux35 V2 External ELRS Analog Version
CRUX35 is an ultra-lightweight 3.5Inch FPV Freestyle FPV Racing Drone, the weight of the whole drone is only 87g for the analog version. The Crux35 serials drone use Happymodel EX1404 high-efficiency motor and HQPROP 3.5-inch three-blade propeller to ensure the largest thrust-to-weight ratio under the most efficient premise, which can bring you a smooth Freestyle […]Rp2.320.000 -
Happymodel CruxF405HD ELRS AIO 3in1 Flight Controller for Digital HD Toothpick FPV Drone
The CruxF405HD ELRS AIO flight controller comes with integrated UART 2.4GHz ExpressLRS receiver and 20A Blheli_s ESC(Bluejay firmware pre-installed) which could support 3-4s battery. Bigger Mosfet could support high to 20A currents would be better for 3-4S toothpick drone or long range FPV drone. Reserved 6 pin socket for DJI HD equipment plug and play. […]Rp810.000 -
Happymodel ELRS EPW6 TCXO 2.4GHz 6CH PWM RC Receiver
Specifications: Item: Happymodel EPW6 TCXO 2.4GHz pwm receiver ESP8285, SX1280/1281 Antenna connector: IPEX MHF 1/U.FL 6x PWM outputs RF Frequency: 2.4GHz (2400~2480MHz) Telemetry power: 12dbm Receiver protocol: PWM or CRSF Input voltage: +5v~8.4v PCB size: 19mm x 17.5mm Weight: 1.49g / antenna Firmware: Target option1: Generic ESP8285 6xPWM 2.4Ghz RX PWM receiver via 1~6 PWM […]Rp200.000 -
HappyModel ES24TX Pro ELRS Transmitter Module
The ES24TX Pro Micro ExpressLRS TX module is a upgrade version of ES24TX module. Max output up to 1000mw, reserved Cooling Fan and RGB LED module. This Micro TX module support most of the OpenTX radio transmitter that with Micro JR bay. And this time the ES24TX Pro module comes completely assembled before out of […]Rp595.000 -
Happymodel ES24TX Slim Pro ELRS Transmitter Module
This Slim Pro TX module is designed by Happymodel and based on the open source- ExpressLRS which is a very popular low latency and high packet rate RF module for RC Airplane and FPV Racing drone. Its main hardware architecture is ESP32, ESP8285 and SX1280 RF chip. The ES24TX Slim Pro module is a complete […]Rp675.000 -
Happymodel ES900RX 915MHz ELRS Receiver
OVERVIEW: ES900TX and ES900RX modules are a set of Long Range 915MHz/868MHz(optional) wireless transmission equipment developed and designed based on the open source software ExpressLRS. This set of modules is characterized by ultra-long range, stable operation and low latency. The module is compatible with most Opentx remote controllers, especially suitable for Radiomaster TX16S and Jumper […]Rp165.000 -
Happymodel ES900RX 915MHZ Replacement T Antenna (UFL / IPEX1)
Frequency: Comaptible with both 915MHz and 868MHz Polarization: linear polarization Impedance: 50 Ω Antenna Gain: 2.5dBi(915MHz) 1.5dBi(868MHz) Working Temp: -40~80℃ Humidity: 95%~100% RH RF Cable : RG1.13 Connector: IPEX1 Weight: 3.57 g Cable Length: 80 mm Width: 140mm Compatibility: Happymodel ES900RX , and other 900MHz ExpressLRS receiver with IPEX Connector,TBS CROSSFIRE NANO RX Package: 1x […]Rp41.000 -
Happymodel EX0802 Brushless Motor 1mm shaft
Specifications: Brand name: Happymodel Item name: EX0802 brushless motor KV: 14000KV 19000KV 22000KV 25000KV optional Shaft Diameter: 1.0mm Configuration: 9N12P Stator Diameter: 8mm Stator Length: 2mm Motor Dimension(Dia.*Len): Φ10.5mm*14.9mm Terminals: JST1.25mm No. of Cells(Lipo): 19000KV/22000KV/25000KV compatible with only 1S lipo 14000KV compatible with 1-2S lipo Wire length(include connector): 14000KV/19000KV/25000KV: 27mm 22000KV: 40mm Weight: 1.7g 19000KV […]Rp105.000 -
Happymodel EX1103 KV11000 1.5mm shaft Brushless Motor for Mobula8
Specification: Mode: EX1103 KV11000 Configuration:9N12P Stator Diamter:11mm Stator Length:3mm Shaft Diameter:Φ1.5mm Motor Dimension(Dia.*Len):Φ13.5mm*15.5mm Weight(g):3.8g No.of Cells(Lipo):1-2S Compatible with: Mobula8, Bassling, and even DJI Neo 1 Includes: 1x Motor EX1103 KV11000 3x ScrewsRp125.000 -
Happymodel EX1103S KV7000 Brushless Motors 1.5mm shaft
Notice: Larva X v2 version frame were already compatible with 4-hole motors Specifications: Mode: EX1103S KV options: 7000KV Configu-ration:9N12P Stator Diamter:11mm Stator Length:3mm Shaft Diameter: Φ1.5mm Motor Dimension(Dia.*Len):Φ13.5mm*15.5mm Weight(g):3.8g No. of Cells(Lipo): 2-3S Features: High efficiency and smooth Dual bearing design and more balance Better for Toothpick building Compatible with 40mm-75mm propellers Upgrade motor for […]Rp125.000 -
Happymodel EX1202.5 Brushless Motor 1.5mm shaft
Specifications: Mode: EX1202.5 KV option: KV6400 KV8000 KV11000 Configu-ration:9N12P Stator Diamter:12mm Stator Length:2.5mm Out Shaft Diameter:Φ1.5mm Inner Shaft Diameter: Φ2mm Motor Dimension(Dia.*Len):Φ15mm*15mm Weight(g):4.4g No.of Cells(Lipo): KV6400 support 2-3s (Original motors for Crux3) KV8000 support 2-3s (Original motors for Cine8) KV11000 supoort 1s only Included: 1 x Happymodel EX1202.5 Motor 1 x Screw Set Note: These […]Rp135.000
Browse All Categories
Electronic
Battery Charger
Telemetry System